Engine Machine Service, Inc.
865 Summit Ave. / Unit 2
Niles, Ohio 44446

 Business Phone:
330 505-1804

Regular Business Hours:
Mon-Fri 8:00am-4:30



> Order/Contact/E-Mail

 

 

 

We have an automotive and diesel Machine shop located in northeast Ohio.  Visit our webpage at http://www.enginemachineservice.com

You can place your order right from the site. Our Shopping cart accepts  Paypal and most major credit cards.  You do not have to have a paypal acct to use your credit card.

You  can either Email or call me (330-505-1804) if you have any questions.

If Description says OEM  that means that it is an Original Mitsubishi manufactured part.

I set this page up  for  your convenience.  if you have any suggestions please feel free to contact me.

All the parts are stocked unless otherwise noted.  I  Try to keep up on the information on what may be backordered and will adjust the listing as needed.

 

Shipping calculations are based on the dollar amount of the sale ( only way paypal  can set up). there are some with flat rate fees also.  you can enter your zip code on checkout to see the total. 

If we feel the shipping price is excessive  we may at times issue a refund on some of the shipping.  Some of the shipping cost includes  costs of supplies and handling along with the paypal or credit card  fees.

This is an idea of shipping costs

Sale price .01- $29.99 = $7.00 shipping

                $30.00-$49.99 = $10.00 shipping

                $50.00-$99.99 = $13.50 shipping

                $100.00-$249.00 = 18.50 shipping

                $250.00 up = $24.00 shipping

A flat rate fee item may bounce the shipping costs higher,  if you have any questions on that please contact us Before the purchase. All prices are based on US 48 continental states Hi, PR. and AK  may be higher just contact us for those rates. We ship with USPS and UPS.

NO INTERNATIONAL SHIPPING AT THIS TIME!!!

Or if you prefer you can pick them up at our shop.

 

Ohio residents will pay sales tax 6.5%

 

 

Thank you very Much - Randy

Here  is a picture Of My 87 TSI

You can also contact me thru www.Starquestclub.com , www.26liter.us;, www.starquest.i-x.net  I am known as DAD ( Randy) on  the sites.

We gladly accept Paypal  ( Paypal to: Enginemac1@aol.com) we also accept Credit cards by phone.

My Email address is Enginemac1@aol.com

I source out Quality parts from PEP, SBI, Melling, Sealed power, ARP, Martin wells,  Marnal, Mitsubishi, Fel Pro, PCI, and Wiseco. along with our rebuilding of engine components.

 

2.6 G54B Conquest / Starion Turbocharged Engine Parts.

TIMING KITS

3 piece Balance shaft elimination kit with chain, plug for upper bal bore and oil pump plug- No Gaskets  $17.49

6 piece Balance shaft elimination kit with Lower chain guide, both gears, chain, plug for upper bal bore and oil pump plug- No Gaskets  $39.95

Add   the cam timing kit below to replace all timing components and balance shaft elimination.

 Complete camshaft timing kit ,new cam and crank gear, cam chain, all guides,Tensioner, No gaskets, No balance shaft parts. $46.99

Use along with or without  a balance shaft timing kit or elimination kit to complete  a timing replacement.

 

 

Balance shaft timing kit ,new crank drive gear, balance shaft chain, 2 balance shaft gears, 3 chain guides and pivot bolt, No cam timing parts or gaskets. $69.99

This kit is used if you are planning on keeping the balance shafts. Add a cam timing kit and it will take care of all timing components.

 

 

ARP FASTENERS

ARP Rod bolt set for 4 rods. $41.99

 

ARP Head stud kit. $117.09  

 

    ARP Moly Lube 1.69 oz Tube $11.27

 

GASKETS AND SETS

  Fel pro Head gasket set HS9116PT  All gaskets needed to remove and install the cylinder head. Even includes turbo mounting gaskets. Add this to the lower conversion set and that makes a complete engine gasket set. $105.49

Fel pro CS8788-1 Conversion ( lower end gasket set) includes front an rear seals- add this to a head gasket set and that makes a complete  engine gasket set.    $56.16

 

Timing cover gasket set, Cover gasket, front seal and water pump gasket $8.95

 

      Fel- Pro Intake manifold gasket  $6.49

 

 

      

  OEM Mitsubishi Exhaust manifold steel shim gasket; $11.49

 

         Fel-Pro Valve cover gasket with valve cover grommets and semi-circular plug $13.99

     Fel-pro Turbo mounting gasket set $6.99

          Includes turbo to manifold gasket, turbo to down pipe  an oil pipe gasket and copper oil pipe gasket

    Copper water banjo gaskets are NOT in this set.

 

 

 

OEM oil pump mounting gasket- turbo application only. $3.23

 

 

  OEM O/Ring for oil pick up tube. $7.49  

 

BACKORDERED_ MAY NO LONGER BE AVAIL>

 

  OEM O/Ring for oil filter adaptor- inner o/ring. this is used along with the o/ring below. $1.59

 

  OEM O/Ring for oil filter housing to block. This is used along with the o/ring listed above. $8.11

 

          Fel-Pro Oil pan gasket set. $11.99

 

 

AJUSA Metal head gasket- This is the best gasket that Ajusa makes for the 2.6 Turbo. Composite core with 2 steel layers and silicone coating. $54.99

.

 

 

GP Throttle body rebuild kit- includes injector seals -  $23.99

 

 

 

PISTONS / RINGS

 

                         Piston and ring kit - Stock

                           Stock replacement set of sealed power cast pistons and moly rings. Available -030-040 includes piston pins. These are not normally stocked but  ordered on an as    needed basis. lead time is normally just a few days. $165.00

all sizes of these pistons have been discontinued by sealed power

NO LONGER AVAIL FROM SEALED POWER

Set of 4 Sealed Power Hypereutectic pistons (with pins and moly rings) Higher compression than stock ( approx 1/2 point higher) 1.395CD .130D dish X2.670 dia.  Available 020-030-040 OS. $165.00

Note:  we may substitute  HASTINGS Rings  due to limited availability of sealed power rings.

Please Select Size

   .030 PISTONS ARE ON BACKORDER!!!!!

 

  Wiseco  8.0-1 Forged Skirt pistons with Sealed power Chrome Moly rings or hastings due to whats available., pins and locks. Skirt coated for added wear resistance to scuffing.  Can be used with either pressed or  bushed connecting rods  Avail -STD -020-030-040   $525.00    

Note:  we may substitute  HASTINGS Rings  due to limited availability of sealed power rings.

These are a true 020-030-040 oversize ( 3.607) 3.617 (3.627) respectively. 

 

The Wiseco pistons  K555M92 are lower compression and are  3.622 ( .035)   and the K555M925 are  3.7417 ( .055)  I can get those kits if you are interested, just contact me.

OUT OF STOCK ON 020 , 030 and 040- (05-14-12- on order)

 

Please Select Size

 

  Sealed power ring set  for stock pistons, avail std-020-030-040 $65.00

PLEASE NOTE  Rings sets are not returnable.- Be sure you order the correct size. 

OUT OF STOCK on STDsealed power - I now have standard rings in hastings brand.

Please Select Size

 

<

Hastings ring set  for stock pistons and My Wiseco 8-1 pistons, avail std-020 $65.00

PLEASE NOTE  Rings sets are not returnable.- Be sure you order the correct size. 

Please Select Size

 

CYLINDER HEADS /PARTS

 

I also have the M28 head casting available for $290.00  that includes shipping.  It is a NON JET  bare head   the intake and exhaust studs are included-  Comes with the new cam towers and bolts, guides and seats installed- ready for assembly. Direct replacement for yor G54B. you can contact me if you have any questions.     **** $290.00 Shipped!

 

 

 

                                Marnal  head assembly,, Brand new  SPAIN casting. 8V  non jet head with  intake and exhaust studs. assembled with 1.00 OS stainless valves, New valve seals, Schneider HD6610   springs, new Retainers, spring seats and keepers. set up to accept up to .500 valve lift. These are the short valves used in 86-89 model years. Just add your cam and rockers and you are ready to go. Intake and exhaust manifold studs are included as well as the cam towers..  $887.00 

***********  OUT OF STOCK      *We will build these as an on order basis  contact me for lead time. Due to spring seats being discontinued we will most likely need

your retainers and spring seats shipped to us for assembly.

 

 

 

    Marnal  head assembly,, Brand new  Spain casting. 8V  non jet head with intake and exhaust studs. assembled with Stock valves, New valve seals, Schneider HD 6610 springs, new Retainers, spring seats and keepers. set up to accept up to .500 valve lift. These are the short valves used in 86-89 model years. Just add your cam and rockers and you are ready to go. Intake and Exhaust studs are included as well as the cam towers.  $765.00

 

***********  OUT OF STOCK      *We will build these as an on order basis  contact me for lead time. Due to spring seats being discontinued we will most likely need

your retainers and spring seats shipped to us for assembly.

 

 

Set of 8 SBI Hydraulic stock replacement lifters  $44.99

 

1 set of 8 Fel pro Viton valve Seals includes installation sleeve  $16.99 Fits stock heads and guides.

 

Please note that if you are replacing seals on a Marnal head that WE assembled and set up for .500 lift that a different seal is used. Please contact us for the correct seal.  These are only the heads with guides cut to clearance  a .500 valve lift.

 

1 set of 16valve SBI keepers (Round Groove) $6.50

 

  1 set of 10  Precision engine parts Stock replacement head bolts $26.95

 

 

JET Valve elimination kit ( 4 bolts and o/rings) $18.95

 

 

Set of one piece STAINLESS 21-4N Intake and Exhaust valves for 2.6T engines from 1985-1989 Valve head diameters are 1.0mm larger head dia. than stock -Swirl Polished and undercut stem. Hardened tip and keeper groove Ex valve 1.535 X 8MM stem X 4.170 round keeper groove Int Valve 1.850 X 8mm stem X 4.250 round keeper groove  $99.95

 

 

     Set of 4 MARTIN WELLS intake and exhaust valves. Stock replacement Fits Mitsubishi- Chrysler DODGE 2.6 G54B Turbo engines 86-89 Round keeper groove style. TURBO APPLICATIONS REQUIRE A STELLITE EXHAUST VALVE  - EXHAUST valve- 1.493 head Dia X 4.170 length .312 stem 45 degree STELLITE -- INTAKE valve- 1.810 head dia.X 4.250 length .3134 stem 45 degree   $49.95

 

 Stock Replacement valve springs- set of 8 by SBI   $25.99

 

Schneider 6610 Heavy duty valve spring kit 100lb seat pressure @ 1.600. Open pressure @ .500 is 180lbs Coil binds@ .900 Set of 8 springs. $44.00

 

 

 

Complete set of valve guides  4 intake and 4 exhaust guides $13.98

If you are replacing the guides in a Marnal head you will need to remove them and let me know the OD- they my be .002 bigger OD than stock.

 

      New Sealed Power Hydraulic Camshaft. Stock replacement  $115.00  

 

OUT OF STOCK   OUT OF STOCK

 

      New Mechanical Camshaft . Stock replacement  $115.00  

 

Set of 8 OEM Valve spring seats- goes between valve spring and cylinder head. $8.50  OUT OF STOCK

OUT OF STOCK-  Save your old ones, I'm told these are no longer available.

 

Set of 8 OEM Valve spring retainers  goes on top of springs, for 86-89 - using round keeper groove locks. $12.96  a set

 

     Rocker arm Adjusting screws for mechanical rockers, These are the long adjusting screws.  $2.03 ea.

 

 

Connecting rods

Set of 4 Race prepped Connecting rods, Magnafluxed, polished beams, shot peened, Reconditioned with ARP rod bolts, Bored on center 6.535 and full round bronze bushing installed. Fit to .0006 clearance oil hole drilled and rods  are then balanced. These rods must be used with pistons that have lock rings for the piston pin.  SOLD OUT-But we can do your rods.Info on bottom of page.

  Set of 4 Race prepped Connecting rods, Magnafluxed, polished beams, shot peened, Reconditioned with ARP rod bolts, and balanced.  These rods are  press fit  only. SOLD OUT-But we can do your rods.Info on bottom of page.

Replacement connecting rod, reconditioned stock connecting rod $34.95 ea.

 

BEARINGS

 

Set of 4 connecting rod bearings- Sealed Power. Available in STD-010-020-030 $29.50

Please note- Bearings are not returnable- Be sure of your size!

 

 

Select a size

 

Sealed power  Balance shaft bearing set  $16.00

I really recommend you replace this if you are keeping the balance shafts.

 

Main bearing set - Sealed Power (federal mogul) Available. STD- 010-020-030 $44.00

Please note- Bearings are not returnable- Be sure of your size!

chose a size

 

Clevite 77 Connecting rod bearing kit.  Std- 010-020-030  -     $22.50

 

Please note- Bearings are not returnable- Be sure of your size! ****

Select a size

  

Clevite 77 Main bearing kit Available Std -010-020-030  $35.00

 

Please note- Bearings are not returnable- Be sure of your size!

Select a size

 

 

OEM Oil Pump.  Turbo application only $245.70 

 

 

OTHER ENGINE PARTS

 

Brass soft plug kit for the engine block. $18.99

 

 

 

NEW OEM Exhaust manifold- Turbo application. Comes with turbo mounting gasket, 4-Turbo studs, Manifold to head gasket and 8 Exhaust lock nuts.    $299.99

 

NEW OEM Exhaust manifold- Turbo application ( STRESS RELIEVED!!). Comes with turbo mounting gasket, 4-Turbo studs, Manifold to head gasket and 8 Exhaust lock nuts. Webbing between the ports cut and manifold resurfaced. $339.99

 

 

Set of 8 OEM Exhaust manifold studs ( Manifold to cylinder head) $23.80

 

Set of 8 OEM Exhaust manifold mounting washers $9.75

 

Set of 8 new OEM self locking exhaust manifold mounting nuts. $6.00

Set of 10  OEM intake manifold mounting studs $16.20

 

Set of 10 OEM  intake manifold lock washers. $1.99

Set of 10 OEM Intake manifold mounting nuts $12.55

4 New OEM Banjo nut washers for oil cooler and oil cooler bypass fittings- requires 1 set for oil cooler and 1 set for the banjo fitting lines on oil filter bypass $8.69 set ea.

These are not in any of the gasket sets.

 

OEM Dowel for end of crankshaft. 88-89- has this dowel. If you are up grading your flywheel to a Fidenza  or have an 87 or older crank and your flywheel has a dowel hole you can use this dowel. BE SURE YOUR FLYWHEEL IS DRILLED FOR THIS DOWELL BEFORE PRESSING IN THE CRANK. All the cranks are drilled but pre-88 flywheels are not. $4.00

Set of 4 OEM Copper gaskets for the Turbo coolant line banjo fitting $3.78

 OEM Copper gasket, used on top oil line fitting for turbo and also on the fuel filter  banjo bolts  $1.51 ea.

 OEM Turbo oil feed fitting, this fitting screws into the turbo and the oil feed line fastens to it.

 Uses copper gasket listed above.  $10.99 ea.

 

 

Set of 6 OEM bolts to fasten pressure plate to flywheel $7.94

Set of 6 OEM Bolts to fasten Flywheel to crankshaft. ( Shallow bolt head) $17.98

Set of 4 New OEM Studs to fasten turbo to exhaust manifold sold individually

4 required to mount turbo  $4.62ea.

OEM Nuts to fasten Turbo to exhaust manifold sold individually- 4 required to mount turbo also used from Turbo to down pipe.- 3 required. $10.53 ea

         Mounting stud From Turbo To Down pipe sold individually requires 3  $5.94 ea

  Set of 4 New OEM  Washers for mounting Turbo to exhaust manifold - this same washer is used on turbo to down pipe.           $4.40 set

 

New OEM Molded Pcv hose. PCV to throttle body $11.37

New Oem Rubber coolant hose 5.5" long goes from thermostat housing to Turbo coolant line. $8.32

New OEM Molded coolant hose from throttle body rear to water side of intake. $8.49

     OEM S shaped coolant hose- rear of intake to water tube.  $18.36

New OEM Turbo coolant Supply line $18.17  

   Goes from turbo down to water pump or just behind the water pump.

 

New OEM Turbo Coolant Return line $22.62  

      This is the line that goes across the front of the valve cover to thermostat housing.

New OEM Turbo oil return braided hose. $19.99 

 

OEM Turbo steel OIL Feed line  $13.04  

 

New OEM Injector seal kit. all 6 seals for the injectors. $17.79

New OEM Pcv Valve For Turbo applications $7.69 

 

        Pack of 2 Dowels OEM gear cover to block. $2.00

  Pack of 2 Dowels OEM  Cylinder head to block $4.10

  Pack of 2 Dowels  OEM Tranny to block  $4.41

Set of 2 Bosch style injector clips. $16.50 Pair 

 

 

3- Flywheel dowel pins OEM. press into flywheel to locate pressure plate to flywheel $3.75 a set

White Plastic retaining clip for front grill and also the plastic cowling under wipers.  $1.08 ea 

     Hood Prop rod Grommet  $1.39 ea 

Used along with the Hood prop rod clip below.    

      Hood Prop rod retaining clip ( yes the one that's always broken!)  $2.43 ea

  Used along with the hood prop rod grommet listed above.     

Front crankshaft pulley repair sleeve. if your front  pulley has a groove where the seal rides you can install this sleeve to re-new the surface $31.99

 

 

Rear crankshaft sleeve. Install this sleeve if your rear seal has worn a groove in the rear of the crank.

saves you from having to get the seal surface welded and reground.  Be sure on installation that you allow room for the flywheel

flange to clear.   $38.99

 

          OEM Hood release cable- for 87-88-89 model years.  Brand new cable assembly  $19.99 ea 

    OEM Brake pedal pad / clutch pedal pad - replace that worn rubber pedal cover ,Brand new  $2.50 ea

 

           OEM Accelerator pad cover- replace that worn rubber pad  $5.99 ea

        OEM Steering socket coupler- this is the coupler that gets worn and allows play in the steering- just between steering shaft and gear box New  $113.26 ea

 _      OUT OF STOCK ----NO LONGER AVAIL.

      OEM Steering socket coupler clamp- this is the clamp for the coupler to the steering box shaft.  $3.99 ea

**  OUT OF STOCK*** NO LONGER AVAIL>

      OEM Steering socket coupler rubber boot- cover for the coupler itself  $3.50 ea

*****  OUT OF STOCK  *** NO LONGER AVAIL.

     OEM Fusible link- Black-  $3.32 ea

       OEM Fusible link- Brown-  $4.85 ea    

       OEM Fusible link- RED-  $6.79 ea

 

     OEM Fusible link- Green-  $4.47 ea

            OEM Relay rod- also known as center link for  steering   $197.59   

OUT OF STOCK +++++++++++ OUT OF STOCK**************** OUT OF STOCK

 

     OEM Front strut insulators- also called front strut bearings- sold as pair  $147.50 pair

 

     OEM Front strut- Rubber dust cover ( boot)  $11.46 ea

     OEM Rear strut rubber dust cover ( boot)  $11.46 ea

OEM Rear differential mounts- the 2 mounts for the rear differential ( pumpkin) sold as a pair  $69.44 pair  

                     OEM Torque Tube Mount. this is the upper mount  2 are required-- $16.27 ea. 

 

                 OEM Torque tube Mount.  This is the lower mount  2 are required - 16.27 ea 

 

 

                      OEM Clutch fork assembly ( yes it has that little spring clip attached)       $83.03

 

 

        OEM Fuel filter - requires 4 copper  banjo gaskets (not included) - $24.11- 

 

                          OEM in the tank fuel filter screen -$6.61  

 

Center wheel cap OEM for 7"-8"-9"Wheels.  $14.33 ea

 

 

Prices subject to change without notice. Subject to prior sales.

 

Labor Prices  on the G54B,  these prices do not include parts.

Head labor is not listed as we prefer to use new head castings listed above in our site. if you have any questions feel free to contact Randy

Crankshaft work

Clean, Magnaflux, check and polish crankshaft  ( if grinding is not needed)                      $76.25

Clean, Magnaflux check, grind Rod and Main journals and polish crankshaft                 $177.25

Balance crankshaft                                                                                                             $75.00

 

Connecting rod work

Press 4 pistons off/on rods                                             $54.00 set

Recondition rods ( install arp bolts)                                 $108.00 set

Balance rods                                                                $75.00 set

Magnaflux rods, polish beams, shot peen, recondition bearing end and balance         $245.00 set

Magnaflux rods, polish beams, shot peen, recondition bearing end and bore for bushings in pin end and balance      $350.00 set

Parts not included and are extra.

Cylinder block work

Degrease block, Magnaflux block, bore and hone ( w/torque plate), Resurface deck, check main bores, install new soft plugs  $400.00

Parts extra.

Assembly

Assemble short block (  install crank, rods, pistons, oil pump and timing components   $ 299.00

 

Assemble long block ( short block assembly, cylinder head, rear seal etc, basically valve cover to oil pan and front pulley to flywheel.

This also includes pressure prime of the oil system                                                         $599.00

Teardown of engine or cylinder heads will be billed at hourly shop rate.

 

 

 

Created and Maintained by: Engine Machine Service, Inc..